Basic Scanning Tips
Place each scan about 8 to 12 ft apart (2.5 to 3.5 m). Shorten to 5 to 8 ft (1.5 to 2 m) or even shorter if you experience alignment issues. For empty spaces, you can place around 10 ft from the wall.
Every scan should be in line-of-sight with a previous scan. This is more important once the walls go up and the construction site is crowded with equipment.
For empty ‘shell’ buildings, 3D Scan the perimeter first. Then take 360º Views at key points in the middle. Learn more about 360º Views.
See an example of a scanned empty building using the technique illustrated on the left.
Take more scans in the important areas. What’s important depends on you and your stakeholders. These can be server rooms, MEP rooms, or other areas. Stakeholders want to review these areas in detail, so take multiple scans at different angles and heights.
Switch to “360º View” mode to scan outside.
360º Views are great for a “curb view” of the site. They are also a great way to capture significant items outside such as a sewage tank, air conditioning unit, or the roof.
You can take a 360º View at any time. 360º Views do not collect 3D data (will not be included in a point cloud file or dollhouse) and aren’t aligned to other scans, so there are no alignment issues. Learn more about 360º Views.
Scan the inside first, then scan the outside. You can use 3D Scan mode to scan outside, such as to scan a path to a detached building. However, this is not supported.
Save outside scans to the end, even if there are only a few. This avoids alignment issues that may domino and cause all proceeding scans to be properly aligned. Learn more about scanning outside. Consider using the 360° View option outside.
Scanning Around Others
Keep it simple and scan when the site is empty such as on the weekend. When people appear in the scan, it looks bad and causes alignment issues.
You can still scan if people are around. Just make sure they don’t appear in the camera’s field of view while it is scanning.
Keep people at least 15 ft (4.5 m) from the camera so they won’t contribute 3D depth data and cause alignment issues.
However, they will still appear in the 2D panorama (Inside View in 3D Showcase).
Point the camera to a high-traffic area and then scan.
If someone walks into the camera’s field of view, quickly tap X to cancel the scan. Point the camera to the high-traffic area and then try again.
The camera will always rotate in a clockwise direction. The camera rotates and stops six times, at each 60º sector.
Scanning for Milestone Documentation
Construction documentation is most useful when you have multiple Matterport Spaces that show the same building at different phases of construction, such as after a concrete pour and before drywall goes up.
You can then compare the view from the same position at different phases to see what changed across time.
However, to do this you have to scan at the exact same positions every time you scan.
Mark the floor with tape or spray paint after every scan. When you scan again after the next milestone, place the camera in the same locations.
Mark your written 2D floor plan after every scan. If your markings are lost or covered up, refer back to the plan.
Stairs, Ceilings, & Floors
The Matterport camera captures data across all 360 horizontal degrees, but there are some vertical limits. For most cases, scanning at normal eye level is good enough.
Upper Limits (Ceilings)
For normal ceilings up to 25 ft (7.5 m) high, the camera will capture the ceiling perfectly fine. Just place the camera at normal eye level (5 to 6 ft, or 1.5 to 2 m).
Areas with double or triple-high ceilings such as a cafeteria or a grocery store can be scanned with extra-tall tripods.
In addition, you may also want more 3D data of what’s on the ceiling, such as the ventilation ducts, so you can generate a better point cloud for BIM. Or you may just want better 2D imagery of the HVAC or electrical for closer inspection.
First take a scan at eye-level height. Then extend the tripod as high as possible and take another scan.
We suggest using an extra-high tripod such as the Manfrotto 028B that can extend up to 8 ft (2.5 m).
Lower Limits (Floors)
The camera can easily capture the floor. Just place the camera at eye-level and scan like normal.
If the object you’re scanning for BIM is very close to the floor, or if the details are right on the ground, then it helps to take a low scan.
Lower the tripod as low as it can possibly go, around a height of 3 ft (1 m).
Use a low scan to help “fill in the black areas” that you see in the Capture app and capture more detail in the 2D images of the floor. Learn more.
Follow all safety rules and regulations while on-site. For example, wear a hard hat, bright neon vest, etc.
The camera is a delicate piece of machinery -- handle carefully!
The camera’s operating temperature is 50º to 90º F (10 to 32° C). See Pro2 camera specifications.
- Do not use or leave the camera at very high temperatures. For example, in strong direct sunlight or in a vehicle in extremely hot conditions. The battery performance will degrade and its service life may decrease.
- The camera should be stored at room temperature. If the camera is not used regularly, then take it out once every 3 months and charge it.
The camera is generally safe, but is not “intrinsically safe” for hazardous situations such as very high temperatures, chemical factories, etc.